fbpx

Inseego MiFi Xpro 5G - Quick Start Guide

What’s included?

Inseego Mifi
USB 3.1 Gen 1, type A to C cable

Inseego MiFi Xpro 5G

USB 3.1 Gen 1, type A to C cable

Step 1: Set up with the Inseego Mobile app

Scan the QR code to install the Inseego app from AppStore or Google Play.

Follow the in-app instructions to set up your device. 

Use the app to configure and customize your device. 

QR Code

Step 2: Install a SIM Card

Check if the SIM card was pre-installed by your service provider. If not, follow these steps to insert your SIM.  Note: Make sure the device is turned off before inserting your SIM card. If the device is powered on, remove the plug before proceeding.

The MiFi X PRO 5G supports only Nano SIM cards. To prevent damage to the SIM slot, please select the correct SIM for this device.

 

Nano, Micro, and Mini SIM Card
  • Insert a fingernail at the edge of the battery cover and lift and remove the battery cover. Set the cover aside.
  • Remove the battery from the battery compartment.
  • Lift the SIM access tab by placing a fingernail underneath the white arrow and lifting the tab up and to the right.
  • If necessary, remove the SIM card from the outer card, being careful not to touch the gold-colored contacts.
  • Slide the SIM card into the slot notch first, with the contact points facing down.
  • Close the SIM access tab, place the battery in the battery compartment and replace the cover. The SIM card MUST remain in the SIM card slot when in use.

Step 3: Power On

Important: Before you use your device, charge the battery for at least four hours to ensure a full initial charge.

  • To turn your device on, press and hold the Power button for three seconds.
  • To turn it off, press and hold the Power button for three seconds until you see the Powering Off screen. Then select Shutdown and select OK.
  • Press and release the Power button to wake up the display.

Step 4: Find the WiFi name and password

  • After you turn on your device, the Home screen appears.
  • Select Wi-Fi Name/Password on the Home screen.
  • The information for your primary network will display. Swipe left to see the information for your guest network.

Step 5: Connect to WiFi

  • The device will broadcast its own wireless network and name.
  • Turn on the device you want to connect.
  • On the device, open the list of available WiFi networks.
  • Select the MiFi primary or guest network and enter the password. Once connected to the internet, the MiFi Home screen displays the connected device.

Step 6: Change WiFi network name and password

  • Make sure your device is connected to the primary network. Open a web browser on your connected device and enter http://my.mifi or http://192.168.1.1
  • Select Sign In in the upper right corner of the screen. You can view your Admin password on the device touchscreen by tapping Help > Admin Website. Note: When you first get your MiFi X PRO 5G, this is the same as your primary network’s password.
  • Select the WiFi option.
  • Select the Primary Network tab.
    • To change your WiFi network name, select the Primary Network Name (SSID) text box and enter the new WiFi name.
    • To change your WiFi password, select the Password text box and enter the new password.
  • Select Save Changes. Once you save the changes, you’ll be disconnected from your WiFi network. Connect again using the new network name and password.

Nokia FastMile 5G Gateway - Quick Start Guide

What’s included?

Nokia FastMile 5G gateway

Nokia FastMile 5G gateway

Powercable

Power Cable/Adaptor

Step 1: Download the Nokia WiFi App

If it’s your first time setting up your FastMile 5G Gateway, download the Nokia WiFi App to your phone or tablet and sign in using your MyRogers credentials.

 

 

 

 

 

 

 

 

 

 

 

 

Get It On Google Play
Download on the App Store

Step 2: Insert the SIM card

Make sure the device ISN’T powered on when inserting the SIM card. If the device is powered on, remove the plug before proceeding. 

Check if the SIM card was pre-installed by your service provider. If not, follow these steps to insert your SIM. 

  • Flip device over. 
  • Remove SIM tray from bottom of device. 
  • Place SIM securely in tray. 
  • Reinsert tray back into device. 
Nokia where to insert SIM
Sim Card
5G Home Internet SIM

Step 3: Scan QR code

Using the Nokia WiFi App, scan the QR code on the bottom of your device.

Step 4: Power on

  • Plug in your Nokia FastMile 5G Gateway and push the ON/OFF button
  • LED lights will appear on top of your device once it’s powered on. 
  • Wait 30–60 seconds so the Gateway can search for a 5G signal.

Step 5: Check light status for connectivity

Use the Nokia WiFi App to check signal strength. You can also check signal strength by viewing the LED lights on top of your device.

  • All three (3) LED lights means there’s a very good signal strength
  • Two (2) LEDs means good signal strength
  • One (1) LED means weak signal strength

To improve your signal strength, you can do the following:

  • Move the location of your device (higher is always recommended).
  • Move your device close to a window or outer wall with few obstructions.

Note: Press the TEST button on the side of your Gateway to check the signal strength at any time.

Step 6: Connect to Wi-Fi

It’s time to connect to your Wi-Fi network!

Use the default SSID and Wi-Fi key printed on the bottom of your Nokia FastMile 5G Gateway to connect your devices.

Step 7: Change Wi-Fi network name and password

Use the Nokia WiFi App to change your Wi-Fi name and password anytime!

If you would like to change them now, follow these steps: 

  • Open the Nokia WiFi App. 
  • Tap the Home Network card on the home screen. 
  • Select the edit icon on the bottom to load the ’Change Wi-Fi’ screen. 
  • On the top right, click the pencil icon to change the Wi-Fi name and password of your network. 
  • After you’ve made your changes, tap the check mark to save your changes. 

Note: After changing your Wi-Fi name and password, you’ll need to connect your devices using your new Wi-Fi credentials.